💡 LED parts, assembly, and soldering
A good-looking sign still fails if the light is uneven. This page only covers putting a 12 V or 24 V DC LED strip into the case. Mains 220 V sign wiring and in-wall electrical work should be checked against the qualified-electrical scope for that site first.
A soldering-iron tip is above 300°C. Before you connect the output of the power supply (SMPS), read the label and confirm whether it is 12 V or 24 V. Reversed LED polarity will not light. Too much voltage burns the strip.
🔦 Which LED to choose
| Type | Typical voltage | How the light looks | Use it on | Remember |
|---|---|---|---|---|
| 5050 (60 per meter) | 12 V | You can see the point sources | Small indoor channels | Many products are about 14.4 W per meter |
| 2835 | 12 V or 24 V | More even | Ordinary letters | Watts differ by product. Read the label |
| COB | 12 V or 24 V | Almost no visible points | A thin diffuser cover | The cut interval is longer |
Large letters and long runs are easier at 24 V. For the same brightness the current is lower, so the far end dims less. That dimming is voltage drop.
Cut a strip only on the scissor mark. A cut between marks kills that segment.
🔋 Power-supply size
- Read watts per meter (W/m) on the strip label.
- Multiply by the length you will use.
- Choose a power supply rated at least 1.25 times that result.
| Example | Calculation | Supply to choose |
|---|---|---|
| 5050, 14.4 W/m × 2 m | 28.8 W × 1.25 = 36 W | 12 V, 40 W (about 3.3 A) or larger |
| 24 V, 10 W/m × 5 m | 50 W × 1.25 = 62.5 W | 24 V, 75 W or larger |
If several letters share one supply, add every watt. The headroom is for heat and life, not for extra brightness.
🧰 Parts worth having
| Part | Starting point | Use |
|---|---|---|
| Temperature-controlled iron | A tip you can set to 320–350°C | Soldering LED pads |
| Solder | 0.6–0.8 mm, flux core | Wets the pad in a short contact |
| Flux pen | No-clean, or a flux you can wash off | When a pad will not take solder |
| Wire | 20–18 AWG for a short 12 V run | Go thicker when the current is higher |
| Heat-shrink | 3–5 mm | Prevents shorts and strain |
| Connector | A 2-pin connector with visible polarity | Lets you separate letters |
| Aluminum channel | One that matches the strip width | Pulls heat out and keeps the line straight |
| Diffuser | Frosted acrylic, or a channel cap | Turns points of light into a surface |
| Fastening | The stock tape, plus silicone if needed | Stops corners from lifting |
| Multimeter | Voltage and continuity | Check before you power on |
If solder will not wet the iron tip, clean the tip and add a little flux before you raise the temperature.
🔥 Soldering sequence
Practice on one letter and one piece of strip before the real job.
- Work with the power supply unplugged from the wall.
- Cut the strip on a scissor mark so the copper pads are visible.
- Strip 3–4 mm of wire, twist it, and tin the wire with the iron first. That pre-tin is a small amount of solder on the wire before it touches the pad.
- Tin the pad very briefly. Do not hold the tip on the pad for more than about 2 seconds. The LED chip will die.
- Join + to + and − to −. On some addressable strips the arrow is signal direction. On a single-color strip, trust the polarity printed on the strip.
- Slide heat-shrink on before you solder, then heat it over the joint.
- Check with a multimeter that + and − are not shorted, then apply power briefly and look at color and brightness.
Do not breathe the solder smoke. Ventilate, and wash your hands after the job. Do not blow on a joint to cool it. Moisture from your breath can make the solder spatter.
🛠️ Putting the strip in the channel
| Step | Do this | Check |
|---|---|---|
| 1 | Measure the inside length and cut the strip | Is the cut on a cut line? |
| 2 | Jump corners with wire | Do not fold the strip at a right angle |
| 3 | Stick it to the inside floor | Are any sections lifting? |
| 4 | Deburr the wire exit hole | Will the insulation be skinned? |
| 5 | Light the sign before the diffuser goes on | Is any section dark? |
| 6 | Close the cover and light it again | If points of light are too strong, add another diffuser layer |
If a run longer than about 2 m is dim at the far end, do not feed it from one end only. Inject power at both ends. The watt calculation and that two-end feed are also in the LED table on Common errors.
✅ After assembly
- Does the strip voltage match the supply voltage?
- Is the polarity correct?
- Can + and − both touch the metal case at once?
- Is a wire pinched by the cover?
- After 10 minutes on, is the power supply too hot to hold comfortably?
Heat is a sign the supply is undersized. Recalculate the watts before you replace it with a larger one.
If the printed face is wavy or a hole does not fit, stop assembly and open Troubleshooting.