Chuyển tới nội dung chính

Large sign splits and slicer bed setup

When one letter is larger than the bed, the split decides the quality. Lock the split line, the joint tolerance, and the placement in the model, then send it to the slicer. A slicer cut does not replace locating pins.

Starting speeds are in High-speed profiles. Extra finishing time from the split goes into Pricing.

Usable bed by machine​

Quote and split against the usable side length, after brim, skirt, and purge line.

MachineOfficial bed (mm)Recommended usable sideNotes
Bambu Lab X1 / P1 series256 × 256 × 256236–240Textured PEI, after flow calibration
Bambu Lab A1256 × 256 × 256236–240Open frame. Watch large flat parts in a draft
Creality K1 / K1C220 × 220 × 250200–205After input shaper is done
Creality K1 Max300 × 300 × 300280–285Check corner level and shrinkage

Treat the height limit as official Z minus 10 mm for the cable chain and clips.

Split rules​

  1. Put the split line where the stroke is thick, not at the thinnest neck.
  2. Do not cross the middle of a visible face. Hide the joint on a side, a rear flange, or a stroke intersection.
  3. Keep the longest side of one part at or below usable side − brim (5–8 mm per side × 2).
  4. Do not rely on a straight butt joint alone. Add at least two locating features.
  5. Engrave the part number, a direction arrow, and an up mark on the back. Height 0.4 mm, stroke width at least 0.6 mm.
Letter conditionSplitWhy
One side is within the usable lengthDo not splitJoint tolerance costs more than it saves
Only one direction exceeds the bedOne cutTwo pins plus a rear flange
Both directions exceed the bedA grid splitKeep a crossing joint off a single line
Serifs or tips are weakKeep the tip in one pieceA split at the tip breaks, and it shows as a step

Joints and tolerance​

Baseline: 0.4 mm nozzle, with outer-wall speed at or below the outer-wall cap in the high-speed profile. Values are labeled as diameter or per-side clearance, not left ambiguous. Confirm one coupon set before production.

JointStarting designA good fitHow it fails
Dowel pin Ø4.0Hole Ø4.25–4.40Goes in by hand and does not rattleAn undersize hole spreads the part
Dowel pin Ø6.0Hole Ø6.30–6.50SameDefault pin for a large channel
Dovetail0.15 mm clearance per sidePlay of 0.3 mm or less after it slidesZero clearance stops on layer lines
Tongue and groove0.15–0.20 mm clearance per sideUse with a rear screw or adhesiveA tongue under 2 mm thick breaks
Rear overlap flangeOverlap 12–20 mm, screw pitch 40–60 mmFrom the front, only the joint line showsOverlap under 8 mm leaves a step
Butt joint plus adhesiveMating-face gap 0.10–0.20 mmThe adhesive layer does not push the faces apartA zero-gap design bulges

Model pin holes as vertical walls, and align the axis with Z so slicer support does not grow inside the hole. For a horizontal hole, use a teardrop (a flattened top) or orient the pin axis with the print direction.

For PETG and ASA, start 0.1 mm larger than the PLA coupon hole and measure again.

Slicer bed setup​

ItemSettingWhy
OriginBed centerAvoids corner temperature difference
SpacingAt least 6 mm between parts. Brims must not overlapStops fused brims and nozzle crashes
Large visible faceOn the bed when you canThe first layer is the most even face
SeamRear, or an aligned seamA random seam on the front becomes a vertical line
SupportKeep it out of joint groovesLeftover support destroys tolerance
BrimOnly on tall, narrow strokes, 5–8 mm wideA brim on every part adds finishing time
OrderDo not park a fragile outline inside the groupA fallen part scrapes its neighbor
Purge / primeSeparate from the model outlineOn a K1, check that the prime line does not stick to the brim

After placement, scrub only the locating-pin layers in the slicer preview. If a bridge is floating inside the hole, do not print that part. Rotate the axis.

Numbering and the assembly map​

  • File name: sign_part_rowcol_material_nozzle, for example ACME_A_R1C2_PETG_04
  • Rear engraving: the short form of the same code, A12
  • One assembly sheet is enough: the split lines drawn on a front photo. Keep it on the job ticket, separate from the customer installation sheet.
  • Dry-fit and measure the full width before adhesive. If the width is off the drawing by more than ±1.0 mm per meter, decide whether the error is stacked joint gaps or shrinkage, then correct the remaining parts.

Record the hole diameter that passed the coupon, with the machine name, in the job log. The next order starts its split tolerance from that value.