メインコンテンツまでスキップ

🛟 Common beginner errors and tolerance

A print rarely works the first time. Read each row as symptom, then the usual cause, then what to try today. Do not change five settings at once. Change one, reprint a small piece, and you will know what worked.

If a word is unfamiliar, go back to the terms guide. The LED assembly order is in Assembly and soldering.

🧹 Thirty seconds before you print​

CheckGoodIf it is not
BedClean, no oilWipe it with alcohol again
First layerLines join, and they are not scrapedAdjust the Z gap
FilamentThe spool is not snaggingCheck the path and the extruder gear
NozzleA straight line comes out at the startPurge, then check for a clog

🖨️ Print symptoms​

What you seeUsual causeTry this
The part will not stick and becomes spaghettiThe bed is too low or dirty, or the first layer is too fastClean the bed, first layer near 20 mm/s, move Z slightly closer
The first layer is crushed and translucent (elephant's foot)The nozzle is too close, or the bed is too hotRaise Z a little, drop the bed 5°C, reduce only the first layer slightly
Corners liftShrinkage, a draft, or a bed that is too coolClose the door, add a brim, confirm PLA bed at 55–60°C
CobwebsTemperature is high, or retraction is weakDrop the nozzle 5°C and leave travel speed alone
Layers shiftBelt, a collision, or speed that is too highBelt tension, and whether the nozzle hits the part
Walls look sparse, with gapsUnderextrusion, or a flow limitCheck for a clog or a slipping gear, then calibrate flow
A screw will not enter the holeThe hole printed smaller than the drawingEnlarge the hole using the tolerance table, then reprint
A cap is looseThe clearance is too largeReduce clearance per side by 0.05 mm and test again
Write the one change on the part

Mark the coupon with a paint pen, for example "hole 3.2 to 3.5, PLA, 0.4 nozzle". That number is what you will want on the next sign.

📐 How to set tolerance​

These are starting compensations for a 0.4 mm nozzle, PLA, and a speed that is not extreme. PETG can print holes even smaller, so print the same size once more in that material.

GoalWhat to change on the drawingStarting size
A screw passes throughEnlarge the holeM3 to 3.4–3.6 mm
A screw cuts its own threadShrink the holeM3 self-tapping, test at 2.6–2.8 mm
A pin goes in by handEnlarge the holePin diameter + 0.2–0.4 mm
A light press fitAlmost the same sizePin diameter + 0.05–0.15 mm
A cap or channel coverClearance per side0.15–0.25 mm
A split letter, buttedDecide after a joint testJoint table in the split guide

The order never changes.

  1. Print a small coupon that contains only the hole or the joint.
  2. Fit the real screw, pin, or mating part.
  3. If it is tight, enlarge the hole by 0.1 mm. If it is loose, reduce it by 0.1 mm.
  4. Write the value next to that printer's name.

Confirm the cause with a coupon before you enable the slicer's XY hole compensation. A global compensation also changes outer dimensions that were already correct.

💡 When the LED is wrong​

SymptomLook here firstFix
Nothing lightsVoltage, polarity, power switchMatch 12 V or 24 V, then swap + and − as a test
It died after a cutThe cut was not on a scissor markDiscard through the next cut line and try again
Only the far end is yellow or dimVoltage drop, or wire that is too thinFeed both ends, use thicker wire, use 24 V for long runs
One segment is deadA lifted pad, or heat damageReplace that segment at the cut lines
It flickers when the cover closesA pinched wire is shortingOpen the cover and find the crushed insulation
The supply gets hot quicklyUndersized supply, or a shortRecalculate watts × 1.25 and remove the short

Test the light with the diffuser open first. You will know immediately whether the problem is the cover or the strip.

🆘 If it is still wrong​

  • Do not shrink the whole model by half. Shrink the test to a coupon that only has the hole.
  • Keep one filament and change only temperature, by 5°C.
  • When you ask for help, include the printer name, nozzle diameter, material, layer height, speed, and a photo of the symptom.

A print shop will already have measured tolerance and speed. Those tables are in High-speed printing and Pricing.