🛟 Common beginner errors and tolerance
A print rarely works the first time. Read each row as symptom, then the usual cause, then what to try today. Do not change five settings at once. Change one, reprint a small piece, and you will know what worked.
If a word is unfamiliar, go back to the terms guide. The LED assembly order is in Assembly and soldering.
🧹 Thirty seconds before you print
| Check | Good | If it is not |
|---|---|---|
| Bed | Clean, no oil | Wipe it with alcohol again |
| First layer | Lines join, and they are not scraped | Adjust the Z gap |
| Filament | The spool is not snagging | Check the path and the extruder gear |
| Nozzle | A straight line comes out at the start | Purge, then check for a clog |
🖨️ Print symptoms
| What you see | Usual cause | Try this |
|---|---|---|
| The part will not stick and becomes spaghetti | The bed is too low or dirty, or the first layer is too fast | Clean the bed, first layer near 20 mm/s, move Z slightly closer |
| The first layer is crushed and translucent (elephant's foot) | The nozzle is too close, or the bed is too hot | Raise Z a little, drop the bed 5°C, reduce only the first layer slightly |
| Corners lift | Shrinkage, a draft, or a bed that is too cool | Close the door, add a brim, confirm PLA bed at 55–60°C |
| Cobwebs | Temperature is high, or retraction is weak | Drop the nozzle 5°C and leave travel speed alone |
| Layers shift | Belt, a collision, or speed that is too high | Belt tension, and whether the nozzle hits the part |
| Walls look sparse, with gaps | Underextrusion, or a flow limit | Check for a clog or a slipping gear, then calibrate flow |
| A screw will not enter the hole | The hole printed smaller than the drawing | Enlarge the hole using the tolerance table, then reprint |
| A cap is loose | The clearance is too large | Reduce clearance per side by 0.05 mm and test again |
Mark the coupon with a paint pen, for example "hole 3.2 to 3.5, PLA, 0.4 nozzle". That number is what you will want on the next sign.
📐 How to set tolerance
These are starting compensations for a 0.4 mm nozzle, PLA, and a speed that is not extreme. PETG can print holes even smaller, so print the same size once more in that material.
| Goal | What to change on the drawing | Starting size |
|---|---|---|
| A screw passes through | Enlarge the hole | M3 to 3.4–3.6 mm |
| A screw cuts its own thread | Shrink the hole | M3 self-tapping, test at 2.6–2.8 mm |
| A pin goes in by hand | Enlarge the hole | Pin diameter + 0.2–0.4 mm |
| A light press fit | Almost the same size | Pin diameter + 0.05–0.15 mm |
| A cap or channel cover | Clearance per side | 0.15–0.25 mm |
| A split letter, butted | Decide after a joint test | Joint table in the split guide |
The order never changes.
- Print a small coupon that contains only the hole or the joint.
- Fit the real screw, pin, or mating part.
- If it is tight, enlarge the hole by 0.1 mm. If it is loose, reduce it by 0.1 mm.
- Write the value next to that printer's name.
Confirm the cause with a coupon before you enable the slicer's XY hole compensation. A global compensation also changes outer dimensions that were already correct.
💡 When the LED is wrong
| Symptom | Look here first | Fix |
|---|---|---|
| Nothing lights | Voltage, polarity, power switch | Match 12 V or 24 V, then swap + and − as a test |
| It died after a cut | The cut was not on a scissor mark | Discard through the next cut line and try again |
| Only the far end is yellow or dim | Voltage drop, or wire that is too thin | Feed both ends, use thicker wire, use 24 V for long runs |
| One segment is dead | A lifted pad, or heat damage | Replace that segment at the cut lines |
| It flickers when the cover closes | A pinched wire is shorting | Open the cover and find the crushed insulation |
| The supply gets hot quickly | Undersized supply, or a short | Recalculate watts × 1.25 and remove the short |
Test the light with the diffuser open first. You will know immediately whether the problem is the cover or the strip.
🆘 If it is still wrong
- Do not shrink the whole model by half. Shrink the test to a coupon that only has the hole.
- Keep one filament and change only temperature, by 5°C.
- When you ask for help, include the printer name, nozzle diameter, material, layer height, speed, and a photo of the symptom.
A print shop will already have measured tolerance and speed. Those tables are in High-speed printing and Pricing.