Zum Hauptinhalt springen

💡 LED parts, assembly, and soldering

A good-looking sign still fails if the light is uneven. This page only covers putting a 12 V or 24 V DC LED strip into the case. Mains 220 V sign wiring and in-wall electrical work should be checked against the qualified-electrical scope for that site first.

Before you connect power

A soldering-iron tip is above 300°C. Before you connect the output of the power supply (SMPS), read the label and confirm whether it is 12 V or 24 V. Reversed LED polarity will not light. Too much voltage burns the strip.

🔦 Which LED to choose​

TypeTypical voltageHow the light looksUse it onRemember
5050 (60 per meter)12 VYou can see the point sourcesSmall indoor channelsMany products are about 14.4 W per meter
283512 V or 24 VMore evenOrdinary lettersWatts differ by product. Read the label
COB12 V or 24 VAlmost no visible pointsA thin diffuser coverThe cut interval is longer

Large letters and long runs are easier at 24 V. For the same brightness the current is lower, so the far end dims less. That dimming is voltage drop.

Cut a strip only on the scissor mark. A cut between marks kills that segment.

🔋 Power-supply size​

  1. Read watts per meter (W/m) on the strip label.
  2. Multiply by the length you will use.
  3. Choose a power supply rated at least 1.25 times that result.
ExampleCalculationSupply to choose
5050, 14.4 W/m × 2 m28.8 W × 1.25 = 36 W12 V, 40 W (about 3.3 A) or larger
24 V, 10 W/m × 5 m50 W × 1.25 = 62.5 W24 V, 75 W or larger

If several letters share one supply, add every watt. The headroom is for heat and life, not for extra brightness.

🧰 Parts worth having​

PartStarting pointUse
Temperature-controlled ironA tip you can set to 320–350°CSoldering LED pads
Solder0.6–0.8 mm, flux coreWets the pad in a short contact
Flux penNo-clean, or a flux you can wash offWhen a pad will not take solder
Wire20–18 AWG for a short 12 V runGo thicker when the current is higher
Heat-shrink3–5 mmPrevents shorts and strain
ConnectorA 2-pin connector with visible polarityLets you separate letters
Aluminum channelOne that matches the strip widthPulls heat out and keeps the line straight
DiffuserFrosted acrylic, or a channel capTurns points of light into a surface
FasteningThe stock tape, plus silicone if neededStops corners from lifting
MultimeterVoltage and continuityCheck before you power on

If solder will not wet the iron tip, clean the tip and add a little flux before you raise the temperature.

🔥 Soldering sequence​

Practice on one letter and one piece of strip before the real job.

  1. Work with the power supply unplugged from the wall.
  2. Cut the strip on a scissor mark so the copper pads are visible.
  3. Strip 3–4 mm of wire, twist it, and tin the wire with the iron first. That pre-tin is a small amount of solder on the wire before it touches the pad.
  4. Tin the pad very briefly. Do not hold the tip on the pad for more than about 2 seconds. The LED chip will die.
  5. Join + to + and − to −. On some addressable strips the arrow is signal direction. On a single-color strip, trust the polarity printed on the strip.
  6. Slide heat-shrink on before you solder, then heat it over the joint.
  7. Check with a multimeter that + and − are not shorted, then apply power briefly and look at color and brightness.
Fumes and solder

Do not breathe the solder smoke. Ventilate, and wash your hands after the job. Do not blow on a joint to cool it. Moisture from your breath can make the solder spatter.

🛠️ Putting the strip in the channel​

StepDo thisCheck
1Measure the inside length and cut the stripIs the cut on a cut line?
2Jump corners with wireDo not fold the strip at a right angle
3Stick it to the inside floorAre any sections lifting?
4Deburr the wire exit holeWill the insulation be skinned?
5Light the sign before the diffuser goes onIs any section dark?
6Close the cover and light it againIf points of light are too strong, add another diffuser layer

If a run longer than about 2 m is dim at the far end, do not feed it from one end only. Inject power at both ends. The watt calculation and that two-end feed are also in the LED table on Common errors.

✅ After assembly​

  • Does the strip voltage match the supply voltage?
  • Is the polarity correct?
  • Can + and − both touch the metal case at once?
  • Is a wire pinched by the cover?
  • After 10 minutes on, is the power supply too hot to hold comfortably?

Heat is a sign the supply is undersized. Recalculate the watts before you replace it with a larger one.

If the printed face is wavy or a hole does not fit, stop assembly and open Troubleshooting.